Our client is looking for an experienced engineer for their projects. This a 10-months contract role.
General Description
•The E3 – Engineer is a fully qualified and accredited engineering professional who applies theoretical and practical knowledge to provide engineering design, estimating, planning, and quality management services for low to medium complexity projects and/or operations safely, with quality, within budget, and on time.
...
Advantages
NOTE: The mentioned rates are NOT INC rates. The INC rate range is $69-79/hr
Responsibilities
Experience and Role Accountabilities
•A minimum four (4) years of in a relevant engineering field or equivalent.
•Develop safe engineering solutions by using initiative and judgement to perform activities such as developing designs, analyzing and resolving problems, and interpreting engineering specifications on low to medium complexity assignments for projects and/or operations.
•Assist project or operations management to meet safety, cost, quality, and time objectives by performing activities such as proposing changes in plans and estimated costs, recommending payment for work completed by contractors, preparing progress reports, coordinating work schedules and other similar tasks.
•Participate in company's engineering practice by conducting independent studies and analysis, exercising judgment in selecting and interpreting information, recommending safe engineering designs, and making typical decisions related to standard methods and designs so that company’s engineering standards are maintained.
•Perform periodic tasks independently which may include on-site construction quality control and monitoring to ensure design compliance.
•Engage with company’s senior engineering team where engineering problems are difficult, complex, or unusual to support company’s management of engineering risk.
Important notes:
• Prior to commencement on assignment, the selected candidate must have their own sole practitioner, or the use of their firm’s, Permit to Practice with EGBC.
• BC Registrants provided to company through this assignment shall work under company Professional Practice Management Plan, Quality Management Pillar. The Registrant shall apply their own or their firm’s Permit to Practice Number to work that is Sealed by the Registrant. Retention and preservation of all project documentation produced by the Registrant during their contract with company will be retained by company to satisfy EGBC Bylaws.
Role Specialty: Electrical - Transmission - Lines
Role Specialty Description:
Additional Experience and Role Accountabilities
• This role requires demonstrated experience with the electrical design for Overhead - lines and underground cables for operating voltages from 60kV to 500kV in an electric utility environment.
• Prepare project documentation and deliverables in accordance with company project and Engineering Design Practices (i.e. evaluation reports, specifications, proposals, estimates, design basis', calculations, hazard logs, test plans).
• Prepare design work packages including scope, duration, and level of effort estimates.
• Prepare signed/sealed engineering deliverables as a Professional of Record (PoR) in accordance with EGBC and company Design Practices.
• Provide technical assistance and construction support in the field, and undertake field reviews as required by EGBC.
• Prepare designs for existing and new facilities.
• Perform various engineering calculations in accordance with regulatory and industry standards such as electrical clearances, electromagnetic and electrostatic field calculations and related induction studies, transient over voltage, switching voltages, AC interference, ampacity, radio interference, audible noise, lightning protection, grounding, arcing, soil resistivity, EMTP.
• Prepare designs, drawings, and specifications for electrical systems on Transmission Overhead - Lines such as line surge arresters, line disconnect switches, lightening protection, circuit to circuit separation.
• Prepare reports for internal and external clients detailing investigations, evaluation, analysis, conclusions, and recommendations.
• Provide technical guidance and review of designs prepared by others following established practices.
• Manage design tasks including scope, schedule, and cost.
Work Assignment Requirements:
* Support capital projects (primarily Transmission Overhead Line) to perform safety, workability, and maintainability input to the design as an extension to the Human Factors and Work Methods team at company.
* Familiar with energized work methods and tools and equipment for Transmission overhead line work
* Develop 3D models for work simulation to access live line workability / maintainability / clearances requirements
* Assist capital projects in delivery of job hazard assessments and energized work procedures, rigging, fall protection and rescue plans and any special / custom tools (i.e. yolks) in accordance with internal established processes and practices, regulatory requirements, and industry best practices
* Prefer to have an Engineering degree (preferably electrical, integrated, electro-mechanical engineering, then mechanical, civil and others) recognized by universities in Canada and a registered PEng. with EGBC
* Trade certification in Transmission O/H line work or construction will be considered
* Technical knowledge of hydro-electric Transmission system is preferred (Distribution and Substation second)
* Well-developed technical writing, communication, and presentation skills are necessary to succeed in this position.
* Candidates with experience in work practices on power systems, risk assessment and safety processes are preferred.
* Need for support on Capital projects fluctuates and may affect length of contract / work
Qualifications
Education and Skills
•University graduate in applied science or engineering
•Registered Professional Engineer (P.Eng.) or Professional Geoscientist (P.Geo.) with Engineers & Geoscientists BC or with another jurisdiction and eligible for registration as such with Engineers & Geoscientists BC
•Company uses a Digital Sign and Seal Technology. You may be required to subscribe to a digital seal technology service offered by Notarius
•Familiarity with CAD systems and drawing standardsAbility to use standard industry design/analysis software
• Intermediate MS Office skills (Word, Excel, and PowerPoint)
• Intermediate English skills for professional environment, written and spoken
Additional Education and Skills
• Communicate effectively in English verbally and in writing, specifically technical writing.
Summary
Interested candidates can send over their resumes directly to Srinivas at srinivas.reddy@randstad.ca
Randstad Canada is committed to fostering a workforce reflective of all peoples of Canada. As a result, we are committed to developing and implementing strategies to increase the equity, diversity and inclusion within the workplace by examining our internal policies, practices, and systems throughout the entire lifecycle of our workforce, including its recruitment, retention and advancement for all employees. In addition to our deep commitment to respecting human rights, we are dedicated to positive actions to affect change to ensure everyone has full participation in the workforce free from any barriers, systemic or otherwise, especially equity-seeking groups who are usually underrepresented in Canada's workforce, including those who identify as women or non-binary/gender non-conforming; Indigenous or Aboriginal Peoples; persons with disabilities (visible or invisible) and; members of visible minorities, racialized groups and the LGBTQ2+ community.
Randstad Canada is committed to creating and maintaining an inclusive and accessible workplace for all its candidates and employees by supporting their accessibility and accommodation needs throughout the employment lifecycle. We ask that all job applications please identify any accommodation requirements by sending an email to accessibility@randstad.ca to ensure their ability to fully participate in the interview process.
show more
Our client is looking for an experienced engineer for their projects. This a 10-months contract role.
General Description
•The E3 – Engineer is a fully qualified and accredited engineering professional who applies theoretical and practical knowledge to provide engineering design, estimating, planning, and quality management services for low to medium complexity projects and/or operations safely, with quality, within budget, and on time.
Advantages
NOTE: The mentioned rates are NOT INC rates. The INC rate range is $69-79/hr
Responsibilities
Experience and Role Accountabilities
•A minimum four (4) years of in a relevant engineering field or equivalent.
•Develop safe engineering solutions by using initiative and judgement to perform activities such as developing designs, analyzing and resolving problems, and interpreting engineering specifications on low to medium complexity assignments for projects and/or operations.
•Assist project or operations management to meet safety, cost, quality, and time objectives by performing activities such as proposing changes in plans and estimated costs, recommending payment for work completed by contractors, preparing progress reports, coordinating work schedules and other similar tasks.
...
•Participate in company's engineering practice by conducting independent studies and analysis, exercising judgment in selecting and interpreting information, recommending safe engineering designs, and making typical decisions related to standard methods and designs so that company’s engineering standards are maintained.
•Perform periodic tasks independently which may include on-site construction quality control and monitoring to ensure design compliance.
•Engage with company’s senior engineering team where engineering problems are difficult, complex, or unusual to support company’s management of engineering risk.
Important notes:
• Prior to commencement on assignment, the selected candidate must have their own sole practitioner, or the use of their firm’s, Permit to Practice with EGBC.
• BC Registrants provided to company through this assignment shall work under company Professional Practice Management Plan, Quality Management Pillar. The Registrant shall apply their own or their firm’s Permit to Practice Number to work that is Sealed by the Registrant. Retention and preservation of all project documentation produced by the Registrant during their contract with company will be retained by company to satisfy EGBC Bylaws.
Role Specialty: Electrical - Transmission - Lines
Role Specialty Description:
Additional Experience and Role Accountabilities
• This role requires demonstrated experience with the electrical design for Overhead - lines and underground cables for operating voltages from 60kV to 500kV in an electric utility environment.
• Prepare project documentation and deliverables in accordance with company project and Engineering Design Practices (i.e. evaluation reports, specifications, proposals, estimates, design basis', calculations, hazard logs, test plans).
• Prepare design work packages including scope, duration, and level of effort estimates.
• Prepare signed/sealed engineering deliverables as a Professional of Record (PoR) in accordance with EGBC and company Design Practices.
• Provide technical assistance and construction support in the field, and undertake field reviews as required by EGBC.
• Prepare designs for existing and new facilities.
• Perform various engineering calculations in accordance with regulatory and industry standards such as electrical clearances, electromagnetic and electrostatic field calculations and related induction studies, transient over voltage, switching voltages, AC interference, ampacity, radio interference, audible noise, lightning protection, grounding, arcing, soil resistivity, EMTP.
• Prepare designs, drawings, and specifications for electrical systems on Transmission Overhead - Lines such as line surge arresters, line disconnect switches, lightening protection, circuit to circuit separation.
• Prepare reports for internal and external clients detailing investigations, evaluation, analysis, conclusions, and recommendations.
• Provide technical guidance and review of designs prepared by others following established practices.
• Manage design tasks including scope, schedule, and cost.
Work Assignment Requirements:
* Support capital projects (primarily Transmission Overhead Line) to perform safety, workability, and maintainability input to the design as an extension to the Human Factors and Work Methods team at company.
* Familiar with energized work methods and tools and equipment for Transmission overhead line work
* Develop 3D models for work simulation to access live line workability / maintainability / clearances requirements
* Assist capital projects in delivery of job hazard assessments and energized work procedures, rigging, fall protection and rescue plans and any special / custom tools (i.e. yolks) in accordance with internal established processes and practices, regulatory requirements, and industry best practices
* Prefer to have an Engineering degree (preferably electrical, integrated, electro-mechanical engineering, then mechanical, civil and others) recognized by universities in Canada and a registered PEng. with EGBC
* Trade certification in Transmission O/H line work or construction will be considered
* Technical knowledge of hydro-electric Transmission system is preferred (Distribution and Substation second)
* Well-developed technical writing, communication, and presentation skills are necessary to succeed in this position.
* Candidates with experience in work practices on power systems, risk assessment and safety processes are preferred.
* Need for support on Capital projects fluctuates and may affect length of contract / work
Qualifications
Education and Skills
•University graduate in applied science or engineering
•Registered Professional Engineer (P.Eng.) or Professional Geoscientist (P.Geo.) with Engineers & Geoscientists BC or with another jurisdiction and eligible for registration as such with Engineers & Geoscientists BC
•Company uses a Digital Sign and Seal Technology. You may be required to subscribe to a digital seal technology service offered by Notarius
•Familiarity with CAD systems and drawing standardsAbility to use standard industry design/analysis software
• Intermediate MS Office skills (Word, Excel, and PowerPoint)
• Intermediate English skills for professional environment, written and spoken
Additional Education and Skills
• Communicate effectively in English verbally and in writing, specifically technical writing.
Summary
Interested candidates can send over their resumes directly to Srinivas at srinivas.reddy@randstad.ca
Randstad Canada is committed to fostering a workforce reflective of all peoples of Canada. As a result, we are committed to developing and implementing strategies to increase the equity, diversity and inclusion within the workplace by examining our internal policies, practices, and systems throughout the entire lifecycle of our workforce, including its recruitment, retention and advancement for all employees. In addition to our deep commitment to respecting human rights, we are dedicated to positive actions to affect change to ensure everyone has full participation in the workforce free from any barriers, systemic or otherwise, especially equity-seeking groups who are usually underrepresented in Canada's workforce, including those who identify as women or non-binary/gender non-conforming; Indigenous or Aboriginal Peoples; persons with disabilities (visible or invisible) and; members of visible minorities, racialized groups and the LGBTQ2+ community.
Randstad Canada is committed to creating and maintaining an inclusive and accessible workplace for all its candidates and employees by supporting their accessibility and accommodation needs throughout the employment lifecycle. We ask that all job applications please identify any accommodation requirements by sending an email to accessibility@randstad.ca to ensure their ability to fully participate in the interview process.
show more